Lexco Cable Manufacturers - Locking Brake Levers

Adjustable, over-center locking brake levers. No ratcheting, only “ON” (over-center) or “OFF” positions.
Easy adjusting knob allows 1.6" of cable to increase or decrease cable tension as needed to compensate for wear or load conditions.
Load link is fabricated of 4130 alloy steel. Normal operation capacity 1000 lb.
Ultimate load capacity 3000 lb (non-recurring static load).
Unless otherwise specified, levers include connecting hardware. Supplied with all required clevis pins, washers and cotter pins needed to attach cable. Bolts to connect lever to vehicle are not provided.

Request Information

Unit of Measure

Items	165-508-008 Side Mount Request Quote	165-508-011 Side Mount Request Quote	165-508-023 Flange Mount-Rigid Request Quote	165-508-028 Side Mount Request Quote	165-508-010 Flange Mount-Rigid Request Quote
Description	N/A 2.5 inches (64 mm) wide side plates; one cable, with three alternate sets of cable clamp holes. For cowl, instrument panel, seat riser or frame installation. Kit B815 - supplied with the following hardware: Clevis Pin Cotter Pin Washer Mounting Spacers (2) Cable Clamp Clamp Base Clamp Spacers (2)	N/A 1.5 inches (38 mm) wide side plates; one cable. For cowl, instrument panel, seat riser or frame installation. Kit B834 - supplied with the following hardware: Clevis Pin Cotter Pin Washer Mounting Spacers (2) Cable Clamp	N/A 2.5 inches (64 mm) wide side plates; two cables. For bulkhead, floor or island (doghouse) installation. Note: When considering load requirements, the load on the lever assembly will be the sum of the load in each cable. Wing flange mounting. Kit B835 - supplied with the following hardware: Clevis Pins (2) Cotter Pins (2) Washers (2) Mounting Spacers (2) Cable Clamps	N/A 1.5 inches wide side plates; one cable. For cowl, instrument panel, seat riser or frame installation. Kit B837 - supplied with the following hardware: Clevis Pin Cotter Pin Washer Mounting Spacers (2) Cable Clamp Clamp Spacers (2)	N/A 2.5 inches (64 mm) wide side plates; one cable. For bulk-head floor or island (doghouse) installation. The rigid frame maintains alignment of clevis pin guide slots for improved life of both the pin and side plates. Kit B817 - supplied with the following hardware: Clevis Pin Cotter Pin Washer Cable Clamp Clamp Base 5/16-24 Bolts (2) Nuts(2)
Innermember Fitting @ 3000 lb	N/A CS550-2	N/A CS550-2	N/A 157-047-002	N/A CS550-2	N/A CS550-2
Innermember Fitting @ 1500 lb	N/A CS550	N/A CS550	N/A 157-047-000	N/A CS550	N/A CS550
Conduit Fitting @ 3000 lb	N/A 072 073	N/A 072	N/A 072	N/A 075	N/A 072 073
Conduit Fitting @ 1500 lb	N/A 062	N/A 062	N/A 062	N/A 065	N/A 062
Dim A¹	N/A 3.23 "3.36 "	N/A 2.71 "	N/A 2.38 "	N/A 3.14 "	N/A 1.70 "1.83 "
Dimension B_min.²	N/A 3.87 "4.00 "	N/A 3.35 "	N/A 3.02 "	N/A 3.78 "	N/A 2.34 "2.47 "
Dimension B_max.³	N/A 5.47 "5.60 "	N/A 4.95 "	N/A 4.62 "	N/A 5.35 "	N/A 3.94 "4.07 "
¹ Dimension A is with the lever in full “OFF” position. Use dimension A in calculating cable length. ² Dimension B minimum is with the lever in full “ON” position and adjusted for minimum (CCW) travel. Use dimension B minimum during installation and initial adjustment. Turn knob (CW) to add travel and increase brake pressure setting. ³ Dimension B maximum is with the lever in full “ON” position and adjusted for maximum (CW) travel.